PRIME FLANGER
An extended flanger with stereo spread and controls for the colour of the sweep.
There is a version for bass too: PRIME BASS FLANGER
What it does
PRIME FLANGER is a flanger with more control. You shape the waveform, the diffusion and the feedback in the low and high range (LOW DAMP and HIGH DAMP). TURBO gives a more intense effect.
With the DAMP controls you soften low or high notes in the feedback. That way you can make the effect dark and warm, or bright and sharp.
How to use it
- Set SEPARATION higher for more diffusion in the sweep.
- Use TURBO for a more intense effect in a solo.
- Adjust LOW DAMP and HIGH DAMP to control the feedback in the low and high range.
- Choose SINE in WAVEFORM for a softer movement.
Where it goes in the chain
Before the amp for a rough sweep, or after the amp for a smoother one. In any case before delay and reverb.
Starting points
Wide sweep
RATE 20 · DEPTH 65 · RESONANCE 45 · SEPARATION 90
A slow flanger with plenty of diffusion.
Adjusted feedback
RATE 25 · DEPTH 50 · RESONANCE 40 · LOW DAMP -60 · HIGH DAMP -60
A starting point with different feedback in the low and high range, to fine-tune from.
Fierce solo
RATE 40 · DEPTH 80 · RESONANCE 65 · TURBO ON
An intense sweep for a solo.
Every setting
| Setting | Range | What it does |
|---|---|---|
| RATE | 0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps) | The speed of the sweep: a number from 0 to 100, or a note value such as 1/4 or 1/8D, which follows the tempo (BPM) of the memory. |
| DEPTH | 0 to 100 | How wide the sweep moves. Low stays close to one tone, high opens and closes the sound widely. |
| RESONANCE | 0 to 100 | Feeds part of the effect back in. Higher sounds sharper and more metallic. Too high can get shrill. |
| MANUAL | 0 to 100 | The center frequency at which the effect works. Lower sounds deeper and thicker, higher sounds brighter and thinner. |
| TURBO | OFF / ON | On gives a more intense effect. Switch it on and off to hear the difference. |
| WAVEFORM | TRI / SINE | The shape of the sweep. TRI moves evenly, SINE is softer and rounder at the ends. |
| STEP RATE | OFF / 0 / 1 / 2 … 1/16T / 1/32 (120 steps) | Sets the cycle of the step function, which makes the rate and depth change in steps. Higher gives finer changes. OFF leaves the step function out. |
| SEPARATION | 0 / 15 / 30 / 45 … 165 / 180 (13 steps) | Sets the diffusion, from 0 to 180 in steps of 15. The higher the value, the more diffusion. Try steps until the spread suits you. |
| EFFECT LEVEL | 0 to 100 | The volume of the flanger signal in the mix. Higher gives more sweep, lower lets your own tone lead. |
| LOW DAMP HIGH DAMP | -100 to 0 | LOW DAMP sets the amount of feedback in the low range, HIGH DAMP in the high range. Both run from -100 to 0. Listen for what suits your tone. |
| LOW CUT HIGH CUT | LOW CUT: FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) HIGH CUT: 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | LOW CUT sets the frequency from which low notes are filtered out, HIGH CUT does the same for high notes. FLAT turns the filter off. |
| DIRECT MIX | 0 to 100 | The volume of the dry signal added to the mix. At 0 you hear mostly the effect, higher lets more of your normal tone through. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. PRIME FLANGER in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Modulation
Turn it yourself?
In GX Board, PRIME FLANGER is a device in your rack, with all its controls on the front.