PRIME BASS FLANGER bass
An extended bass flanger with extra controls for tone, waveform and stereo.
The version for guitar: PRIME FLANGER
What it does
This flanger blends in a short delayed copy of your bass and sweeps it, like the standard version. Here you can shape the sweep much further: waveform, stereo spread, damping and filters.
With DIRECT MIX and a LOW CUT you keep the low end firm.
How to use it
- For a calm, floating sweep with the SINE waveform in jazz and soul.
- Turn TURBO on for a stronger, sharper effect in rock.
- Use SEPARATION to spread the sound more, while the core stays firm.
- Use LOW CUT so the effect does not smear the lowest notes, and HIGH CUT to take the sharp edge off the effect.
Where it goes in the chain
Put it after compressor and drive and before delay and reverb. Keep DIRECT MIX higher for an extra firm low end.
Starting points
Silky sweep
RATE 20 · DEPTH 50 · WAVEFORM SINE · DIRECT MIX 40
A calm, round sweep for ballads.
Wide stereo flanger
RATE 30 · DEPTH 60 · SEPARATION 90 · DIRECT MIX 40
A sweep that sounds wide, with the low end still in the centre.
Hard and sharp
RATE 35 · DEPTH 70 · RESONANCE 65 · TURBO ON · DIRECT MIX 50
A pronounced effect for rock.
Every setting
| Setting | Range | What it does |
|---|---|---|
| RATE | 0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps) | The speed of the sweep, free or as a note value. Slow is floating, fast is vibrating. |
| DEPTH | 0 to 100 | How far the sweep reaches. Low is subtle, high gives a big movement. |
| RESONANCE | 0 to 100 | How much of the effect feeds back into itself. Higher sounds sharper and more metallic. |
| MANUAL | 0 to 100 | The centre point the sweep moves around. Lower sounds deeper, higher brighter and thinner. |
| TURBO | OFF / ON | Makes the effect a lot more intense. Use it for a clear, sharp sweep, and leave it off for a softer sound. |
| WAVEFORM | TRI / SINE | The shape of the movement. TRI moves evenly back and forth, SINE is softer and rounder at the turns. |
| STEP RATE | OFF / 0 / 1 / 2 … 1/16T / 1/32 (120 steps) | Sets the cycle of a step function that changes the rate and depth. Higher gives finer steps. OFF switches it off. |
| SEPARATION | 0 / 15 / 30 / 45 … 165 / 180 (13 steps) | Sets how much the sound is spread (diffused), in degrees. Higher gives more spread. |
| EFFECT LEVEL | 0 to 100 | How much of the flanger sound you hear. Higher is more effect. |
| LOW DAMP HIGH DAMP | -100 to 0 | Set how much feedback the low and the high range get. Turn them while you listen. |
| LOW CUT | FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) | Removes the lowest frequencies from the effect signal. Higher leaves the bottom of your bass alone. |
| HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Removes the highest frequencies from the effect signal. Lower makes the sweep darker and softer. |
| DIRECT MIX | 0 to 100 | Blends your clean bass in with the effect. Higher gives a firmer low end and a clearer attack. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. PRIME BASS FLANGER in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Modulation
Turn it yourself?
In GX Board, PRIME BASS FLANGER is a device in your rack, with all its controls on the front.