PRIME BASS PHASER bass
An extended bass phaser with many stages, waveform and stereo.
The version for guitar: PRIME PHASER
What it does
This phaser rotates a phase-shifted copy through your bass, like the standard version, but with a lot more choice: up to 24 stages, a waveform, stereo spread, damping and filters.
With DIRECT MIX and a LOW CUT you keep the bottom end firm.
How to use it
- For a calm phaser with 2 STAGE or 4 STAGE and the SINE waveform in jazz and soul.
- Use 16 STAGE or 24 STAGE for a deep, rich rotation.
- Use SEPARATION to spread the sound more while the bass stays firm.
- Use LOW CUT to keep the low end free from the effect.
Where it goes in the chain
Put it after compressor and drive and before delay and reverb. Keep DIRECT MIX higher for a firm low end.
Starting points
Silky
STAGE 4 STAGE · RATE 20 · DEPTH 40 · WAVEFORM SINE · DIRECT MIX 40
A calm, round rotation for ballads.
Deep and wide
STAGE 16 STAGE · RATE 30 · DEPTH 70 · SEPARATION 90 · DIRECT MIX 50
A rich phaser that sounds wide, with the bass in the centre.
Every setting
| Setting | Range | What it does |
|---|---|---|
| STAGE | 2 STAGE / 4 STAGE / 8 STAGE / 16 STAGE / 24 STAGE | The number of phase stages. 2 and 4 STAGE are soft, 8 and 16 STAGE richer, 24 STAGE is the deepest and most pronounced. |
| RATE | 0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps) | The speed of the rotation, free or as a note value. Slow is floating, fast is vibrating. |
| DEPTH | 0 to 100 | How far the phaser moves. Low is subtle, high gives a big movement. |
| RESONANCE | 0 to 100 | How much of the effect feeds back into itself. Higher sounds sharper and nasal. |
| MANUAL | 0 to 100 | The centre point the rotation moves around. Lower sounds deeper and thicker, higher brighter. |
| WAVEFORM | TRI / SINE | The shape of the movement. TRI moves evenly back and forth, SINE is softer and rounder. |
| SEPARATION | 0 / 15 / 30 / 45 … 165 / 180 (13 steps) | Sets how much the sound is spread (diffused), in degrees. Higher gives more spread. |
| STEP RATE | OFF / 0 / 1 / 2 … 1/16T / 1/32 (120 steps) | Sets the cycle of a step function that changes the rate and depth. Higher gives finer steps. OFF switches it off. |
| BI-PHASE | OFF / ON | Sets whether the two phase shift circuits are connected in series (ON) or not (OFF). On sounds fuller. |
| LOW DAMP HIGH DAMP | -100 to 0 | Set how much feedback the low and the high range get. Turn them while you listen. |
| LOW CUT | FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) | Removes the lowest frequencies from the effect signal. Higher leaves the bottom of your bass alone. |
| HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Removes the highest frequencies from the effect signal. Lower makes the effect darker and softer. |
| EFFECT LEVEL | 0 to 100 | How much of the phaser sound you hear. Higher is more effect. |
| DIRECT MIX | 0 to 100 | Blends your clean bass in with the effect. Higher gives a firmer bottom end. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. PRIME BASS PHASER in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Modulation
Turn it yourself?
In GX Board, PRIME BASS PHASER is a device in your rack, with all its controls on the front.