PRIME CHORUS
A refined chorus with extra controls for softness and shine.
What it does
PRIME CHORUS doubles your sound with a slightly detuned copy, like a regular chorus. It adds two extra controls to colour the character of the swirl.
The result is wide and smooth. You decide how enveloping (SWEETNESS) or how bright (BELL) it sounds.
How to use it
- Set DEPTH low and RATE slow for a clean tone that sounds wider without wobbling.
- Turn SWEETNESS up for an enveloping, round swirl under a quiet solo.
- Use BELL for more brilliance on chords with open strings.
- Choose STEREO in OUTPUT MODE to spread the sound across two sides.
Where it goes in the chain
After the amp or after your clean tone, and before delay and reverb, so the space stays wide too.
Starting points
Silky clean
RATE 30 · DEPTH 35 · SWEETNESS 70 · BELL 40
A soft, wide swirl for a clean tone or quiet chords.
Shiny chords
RATE 45 · DEPTH 50 · BELL 75 · OUTPUT MODE STEREO
Bright and wide, good for open chords and arpeggios.
Dark swirl
RATE 25 · DEPTH 60 · HIGH CUT 3.15kHz · SWEETNESS 60
Warm and muted, stays behind the melody.
Every setting
| Setting | Range | What it does |
|---|---|---|
| RATE | 0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps) | The speed of the swirl: a number from 0 to 100, or a note value such as 1/4 or 1/8D, which follows the tempo (BPM) of the memory. |
| DEPTH | 0 to 100 | How deep the swirl is. Low is subtle and wide, high is obvious and a bit seasick. At 0 you get a doubling effect instead of a swirl. |
| EFFECT LEVEL | 0 to 100 | The volume of the chorus signal in the mix. Higher gives more swirl, lower lets your own tone lead. |
| PRE-DELAY | 0.0ms / 0.5ms / 1.0ms / 1.5ms … 39.5ms / 40.0ms (81 steps) | The time between the dry sound and the effect sound. Short sounds tight. Longer makes it sound as if two guitars play at once (doubling). |
| WAVEFORM | TRI / SINE | TRI gives the typical chorus sound. SINE gives a deeper sense of movement. |
| LOW CUT HIGH CUT | LOW CUT: FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) HIGH CUT: 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | LOW CUT sets the frequency from which low notes are filtered out, HIGH CUT does the same for high notes. A higher LOW CUT keeps the bass tight, a lower HIGH CUT sounds darker. FLAT turns the filter off. |
| SWEETNESS | 0 to 100 | Higher values give a more enveloping sound. Turn it up for a soft, roomy swirl and pick what suits your tone. |
| BELL | 0 to 100 | Higher values give a more brilliant, brighter sound. Turn it up for extra shine on chords. |
| OUTPUT MODE | MONO / STEREO | MONO suits a mono output. STEREO gives a richer sense of space on a stereo output, such as two amps or a stereo system. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. PRIME CHORUS in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Modulation
Turn it yourself?
In GX Board, PRIME CHORUS is a device in your rack, with all its controls on the front.