Contents
  1. 00Before you begin
  2. 01Connecting and first settings
  3. 02Navigating
  4. 03Setting up an effect
  5. 04Amp and cab
  6. 05EQ
  7. 06Noise, comp, drive, modulation, delay, reverb
  8. 07Serial, parallel, two amps
  9. 08Saving
  10. 09Footswitches and expression pedal
  11. 10Looper
  12. 11BOSS Tone Studio on the Mac
  13. 12Recording in Logic
  14. 13MIDI to a synthesizer
  15. 14Troubleshooting
  16. Sources

Your GX-100, step by step

A workbook for your new BOSS GX-100. You control it with the touch screen and the knobs, and on the Mac with BOSS Tone Studio. Every step ends with something you hear or see. Check off what you have done; your progress is kept in this browser.

How to read the controls

WRITE button on the panel 1 knob below the screen EFFECTS tap on the screen C1 footswitch GAIN parameter not verified not confirmed in a source

Checked first

These facts were compared with the BOSS manual.

ClaimResultSource
USB: MAIN = channel 1/2 (processed), DRY = 3/4 (dry)Correct. Roland calls them "GX-100 MAIN (1L, 2R)" and "GX-100 DRY (3L, 4R)".SUP 1, SUP 2
48 kHzCorrect. Sampling Frequency 48 kHz.RM Specs
32 ampsCorrect. 23 guitar amps plus 9 bass amps, all AIRD.Product, PG Amp types, PG Bass preamp
More than 170 effectsCorrect according to the product page. The specifications say "170 Types".Product, RM Specs
15 blocks, of which 2 ampsCorrect. A maximum of 15 effects and function blocks, and a maximum of 2 AIRD PREAMP. The processing power (DSP) can run out sooner.RM Placement, PG Max
8 footswitches and an expression pedal with a toe switchCorrect. BANK ▼, BANK ▲, 1 to 4, C1, C2/TUNER, plus EXP 1 with the EXP1 switch under your toe.RM Specs, Product
200 user memories and 100 factory presetsCorrect. U01-1 to U50-4 and P01-1 to P25-4.RM Memory
MIDI in and out; program change when you change memory; C1/C2 and external pedals send CCsCorrect. One remark: for MEMORY MIDI the Parameter Guide only mentions USB. See chapter 13.RM MIDI, PG Memory MIDI

A bank has four memories. In one place the Reference Manual writes "three", but the numbering (U01-1 to U01-4) and the switches 1 to 4 show four.

BOSS Quick Start videos

Short and official. They open on YouTube.

Source: BOSS Quick Start videos. There is also a video about the Four Cable Method; you do not need it without an amp.

Chapter 01

Connecting and first settings

You play at home with headphones and record over USB. For that you need four connections on the back. The rest can wait.

INPUT OUTPUT RL/MONO PHONES SEND GND LIFT RETURN AMP CTL1, 2 CTL 3,4/EXP 2 MIDI OUTIN BT-DUAL USB POWER DC IN your guitar headphones to synthesizerMIDI IN (ch. 13) MacLogic + Tone Studio adapter amp ormixer (later) effects loop(not needed) amp channels,extra pedals optionalBluetooth
Diagram of the back panel, from left to right. Orange: what you use now. Scroll sideways on your phone.

Source: RM · Connecting the equipment, RM · Specifications.

Steps

  1. Turn everything down. Plug the guitar into INPUT, the headphones into PHONES and the adapter into DC IN. Run the adapter cable through the hook next to DC IN.

    You see: the cable is held in place and cannot come out by accident.

  2. Press POWER. Do not touch the screen while it starts up, or touch will not work properly.

    You see: the start screen. If AUTO OFF is on, it first asks whether you want to set that (SETUP or EXIT).

  3. Do you not want it to switch off after 20 minutes of silence? Press MENU, tap HARDWARE SETTINGS and AUTO OFF, choose OFF and tap OK. Press EXIT a few times.

    You see: you are back on the play screen. Note: when it switches off automatically, everything you have not saved is gone.

  4. Press IN/OUT SETTINGS and tap INPUT SETTINGS (or press knob 1). With 3, set the type to GUITAR. Strike hard and turn 4 (INPUT SENS, -20 to +20 dB).

    You see: the input meter at the top right. Good is: the yellow peak lights up very briefly when you strike hard.

  5. You can store ten of these input settings. Tap NAME EDIT and name this one, for example, "GUITAR". Confirm with EXEC: [WRITE] or WRITE.

    You see: the name in the list. The orange line is the setting that is in use now (SYSTEM).

  6. Press IN/OUT SETTINGS, tap OUTPUT SELECT (or knob 2) and choose with 4 or SELECT: LINE/PHONES (RECORDING). This is the setting for headphones, mixer and recording.

    You hear: the full amp-and-cab sound in your headphones.

  7. Turn OUTPUT LEVEL until the volume is comfortable.

    You see: the output level at the top right of the screen. You hear: everything louder or softer.

  8. The global EQ works on the output, for all memories at once. Press IN/OUT SETTINGS and tap GLOBAL EQ. Set it to ON. If your headphones sound too sharp, turn HIGH CUT down.

    You hear: the highs get softer in every sound, not only in this memory.

    Whether GLOBAL EQ also works on the USB recording: not verified. The Parameter Guide only says "the tone of the OUTPUT".

  9. Tuning: press C2/TUNER. Knob 1 is the reference pitch (440 Hz by default). Knob 2 is TUNER OUTPUT: MUTE (silent), BYPASS (dry, without effects) or THRU (with effects). With SELECT you switch the display. To leave the tuner: press C2/TUNER again or EXIT.

    You see: the tuner screen with the tuning meter. You hear: nothing with MUTE.

Sources: RM · Power, RM · Auto Off, RM · Input, RM · Output select, PG · Output Select, RM · Volume, PG · Global EQ, RM · Tuner, SUP 5.

Check off

Chapter 03

Setting up an effect

A memory is a chain of blocks. The signal runs from left to right. You have a maximum of 15 blocks, of which at most 2 amps, 1 looper, 1 divider/mixer and 1 send/return. Of the same effect you can place at most 9.

INPUT NS COMP OD AIRD PREAMPamp · speaker · mic PEQ CHO DLY REV MASTER PHONESOUTPUTUSB 1/2 noise before the amp max. 2 per memory after the amp always last Example order, not a rule. You can move blocks freely.
This is what a chain can look like. MASTER is the last block; it holds MEMORY LEVEL, BPM and CARRYOVER, among others.

Sources: RM · Effect placement, PG · Max effects, PG · MASTER.

Steps

Practice on a factory preset, for example P01-1 GX DUAL DRIVE. If you switch memory without saving, your changes are gone. If you want to keep something, go to chapter 8.

  1. Tap EFFECTS at the top left or press EFFECTS.

    You see: the effect chain with all the blocks of this memory.

  2. Tap the icon of an effect, for example the overdrive. According to the manual, each tap on the icon switches the effect on or off. You can also press SELECT.

    You hear: the distortion disappears and comes back.

  3. Four parameters are at the bottom. Drag one to the left or right, or turn 1 to 4. With PAGE ◀ ▶ you see the next page; the page number is at the bottom center.

    You hear: with DRIVE (0 to 120) more or less distortion.

  4. Choosing another type: find the parameter TYPE on one of the pages. With OVERDRIVE, for example, you have BLUES OD (BOSS BD-2), T-SCREAM (Ibanez TS-808) and CENTA OD (Klon Centaur).

    You hear: a different character of the distortion.

    Which page TYPE is on differs per effect: not verified.

  5. Everything of one effect on one screen: tap the menu icon at the top right and then KNOB VIEW (or knob 4). Faster: tap the effect and hold SELECT down.

    You see: all parameters as knobs. Drag them up or down. At the bottom, tap another effect name to jump there.

  6. Moving: hold an icon and drag it to the left or right in the chain. With buttons: choose the block, hold SELECT down and turn.

    You hear: for example, chorus before or after the amp sounds different.

  7. Adding: tap EFFECTS PALETTE. At the top are all the effects (guitar first, then bass). Drag one to the spot in the chain and let go when you see the "+".

    You see: the new block in that spot. If the icon in the palette is gray, the DSP is full: remove something first.

  8. Replacing: drag an effect from the palette onto a block in the chain and tap OK.

    You see: the old block is replaced by the new one.

  9. Removing: drag the block from the chain back to the palette. Let go when the palette lights up blue and tap OK (or knob 4). Or: tap the block, the menu icon at the top right, DELETE (knob 1), OK.

    You see: one spot less in the chain. You hear: that effect is gone.

Without touching the screen: EFFECTS switches between palette and chain, SELECT chooses. Insert: press SELECT. Replace: hold EFFECTS and press SELECT. Remove: hold EXIT and press SELECT.

MessageMeaning
CHAIN IS FULL!There are already 15 blocks. Remove one.
DSP RESOURCE IS FULL!The processing power is used up. Remove a block. Heavy blocks include AIRD PREAMP, TERA ECHO, REVERB+, SHIMMER REVERB and ANALOG DELAY.
CAN NOT OVERWRITE!Replacing does not work because there is too little DSP.
THE NUMBER OF SAME FX IS LIMITED TO 9.The same effect is allowed a maximum of 9 times.

Sources: RM · Effect editing, RM · Effect placement, PG · OVERDRIVE, PG · DSP, RM · Errors.

Check off

Chapter 04

Amp and cab

The amp block is called AIRD PREAMP. It is the preamp, the speaker and the microphone in one block. You can use two per memory (chapter 7).

The 23 guitar amps

TypeWhat BOSS says about it
TRANSPARENTWide and very flat. Good for acoustic guitar.
NATURALUnadorned clean, without sharp highs or boomy lows.
BOUTIQUECrunch that follows your picking very precisely.
SUPREMECrunch with the character of a 4x12 cabinet.
MAXIMUMVintage Marshall feel, with more gain.
JUGGERNAUTBig stack for metal.
X-CRUNCH · X-HI GAIN · X-MODDED · X-ULTRA · X-OPTIMA · X-TITANSix MDP types: crunch to tight high gain, keeping definition.
JC-120Roland JC-120.
TWIN COMBOFender Twin Reverb.
DELUXE COMBOFender Deluxe Reverb.
TWEED COMBOFender Bassman 4x10 combo.
DIAMOND AMPVOX AC30.
BRIT STACKMarshall 1959.
RECTI STACKMESA/Boogie Dual Rectifier, channel 2 MODERN.
MATCH COMBOMatchless D/C-30, left input.
BG COMBOMESA/Boogie combo.
ORNG STACKOrange Rockerverb, dirty channel.
BGNR UB METALBogner Uberschall, high-gain channel.

Plus 9 bass types in the AIRD BASS PREAMP block. Sources: PG · AIRD PREAMP TYPE list, PG · AIRD BASS PREAMP.

Amp parameters

ParameterRangeWhat it does
GAIN0–120Distortion.
GAIN SWLOW/MID/HIGHThree gain settings. Every type is built with MID as the starting point.
BASS · MIDDLE · TREBLE0–100Tone control.
PRESENCE0–100The very top end.
BRIGHT SWOFF/ONOnly on some types.
LEVEL0–100Volume of the amp. Do not set it too high.
SOLO SW · SOLO LEVELOFF/ON · 0–100Solo sound and its volume.
SAG-10–+10How strongly the power stage compresses.
RESONANCE-10–+10Interaction between power stage and speaker transformer.
SP TYPEsee belowThe speaker cabinet.
MIC TYPEsee belowThe simulated microphone.
MIC DISTANCESHORT/MEDIUM/LONGDistance from mic to speaker.
MIC POSITIONCENTER, 1–10 cmCenter of the cone or off to the side.
MIC LEVEL · DIRECT MIX0–100Volume of the mic and of the direct signal.

Speaker and microphone

SP TYPE: OFF, ORIGINAL (the cabinet that goes with the amp type), 1x8", 1x10", 1x12", 2x12", 4x10", 4x12", 8x12", the bass cabinets B1x15", B1x18", B2x15", B4x10", B8x10", and USER1 to USER16 for your own IRs.

MIC TYPE: DYN57 (Shure SM57), DYN421 (Sennheiser MD-421, more low end), CND451 (AKG C451B), CND87 (Neumann U87, flat), RBN121 (Royer R-121, warm), BLEND A/B/C (SM57 and R-121 mixed), FLAT (as if you are standing in the room).

Sources: PG · AIRD PREAMP, PG · SP TYPE list, PG · MIC TYPE list.

Steps

  1. Press EFFECTS and tap the amp block. Find TYPE and choose JC-120. Turn GAIN low.

    You hear: a bright clean sound.

  2. Now choose BRIT STACK and set GAIN SW to LOW, MID and HIGH in turn.

    You hear: three steps of more distortion, with the same GAIN knob.

  3. Turn MIDDLE from 20 to 80 while you play.

    You hear: the guitar comes forward in the mids.

  4. With PAGE ▶ go to page 4 and turn knob 3: that is SP TYPE. Switch between 1x12" and 4x12".

    You hear: a smaller cabinet against a bigger one. At the very end of the list are USER1 to USER16.

  5. Switch MIC TYPE from DYN57 to RBN121. Then set MIC POSITION from CENTER to 5 cm.

    You hear: the highs change with every step. Listen especially to the edges of the attack.

  6. You load your own IR on the Mac, with the IR LOADER in BOSS Tone Studio (chapter 11). Files: WAV, 44.1, 48 or 96 kHz, 16 or 24 bit.

    You see: after loading, your IR is in the USER slot you chose, at the end of the SP TYPE list.

Sources: PG · AIRD PREAMP, SUP 4 · Loading an IR, BTS · IR LOADER.

Check off

Chapter 05

EQ

You have three kinds of EQ. The amp has its own tone control. Besides that there are two EQ blocks, and the GLOBAL EQ from chapter 1.

PARAMETRIC EQGRAPHIC EQ
Bands4: LOW, LOW-MID, HIGH-MID, HIGH10: 31.5 · 63 · 125 · 250 · 500 Hz · 1 · 2 · 4 · 8 · 16 kHz
Range-20 to +20 dB per band-20 to +20 dB per band
Choosing the frequencyYes: LOW-MID FREQ and HIGH-MID FREQ, 20 Hz to 12.5 kHzNo, fixed bands
Width (Q)0.5 to 16. Higher = narrowerNo
FiltersLOW CUT and HIGH CUT (FLAT = off)No
VolumeLEVEL -20 to +20 dBLEVEL -20 to +20 dB
Applies toOnly this memory. GLOBAL EQ (same knobs as PARAMETRIC) applies to all memories.

Sources: PG · PARAMETRIC EQ, PG · GRAPHIC EQ, PG · GLOBAL EQ.

Where in the chain

After the amp: you color the sound like a recording EQ. The distortion does not change. Before the amp: you change what the amp has to process, and so also how it distorts. not verified This is a general rule of thumb, not from the BOSS documentation. Try it yourself: move the block (chapter 3) and listen.

Two practical examples

The frequencies below are starting points from recording practice, not BOSS values: not verified. Your ear decides.

  1. Finding the spot. Put a PARAMETRIC EQ after the amp. Set LOW-MID GAIN to +10 dB and LOW-MID Q high (narrow, for example 4). Slowly turn LOW-MID FREQ between 150 and 600 Hz while you play chords.

    You hear: in one spot it becomes noticeably dull and boomy. That is your mud.

  2. Mud gone. Leave the frequency where it is. Set LOW-MID GAIN to -3 to -5 dB and Q to about 1.5. Set LOW CUT around 80 to 100 Hz.

    You hear: chords become clearer and tighter, without the guitar sounding thin. Switch the block on and off to compare.

  3. Presence. Set HIGH-MID FREQ around 2.5 to 4 kHz, Q around 1, HIGH-MID GAIN +2 to +3 dB. If it is too sharp afterwards, set HIGH CUT around 8 kHz.

    You hear: the attack comes forward, the hiss at the top does not.

  4. Graphic alternative. With a GRAPHIC EQ: 250 Hz -3 dB, 2 kHz +2 dB. Coarser, but quick.

    You see: your curve at a glance. You hear: about the same effect as above.

  5. If the whole thing has become too loud or too soft, correct it with LEVEL in the EQ block.

    You hear: block on and off are equally loud, so you only compare the sound.

Check off

Chapter 06

Noise, comp, drive, modulation, delay, reverb

Noise suppressor (NS)

THRESHOLD 0–100: higher with more noise. Too high and soft playing gets cut off. RELEASE 0–100: how fast it closes. DETECT: normally INPUT. If a delay or reverb sits before the NS, choose NS INPUT so the tail is not cut off.

  1. Switch on a high-gain amp and play nothing. Switch on the NS and turn THRESHOLD up until it is quiet.

    You hear: the hiss between your notes disappears.

  2. Let a chord ring out. If the end sounds pinched, turn THRESHOLD back a little or RELEASE a little higher.

    You hear: the chord fades away naturally.

Source: PG · NOISE SUPPRESSOR.

Compressor

COMPRESSOR has three types: BOSS COMP (BOSS CS-3), D-COMP (MXR Dyna Comp), ORANGE (Dan Armstrong Orange Squeezer). Knobs: SUSTAIN, ATTACK, LEVEL, TONE, DIRECT MIX. X-COMPRESSOR uses MDP and also has RATIO (1:1 to INF:1).

  1. Put a COMPRESSOR before the amp, type BOSS COMP. Play soft and hard notes and turn SUSTAIN up.

    You hear: soft and hard notes come closer together, and notes ring longer.

  2. Too flat? Turn DIRECT MIX up.

    You hear: the attack comes back, with the sustain kept.

Sources: PG · COMPRESSOR, PG · X-COMPRESSOR.

Overdrive and booster

OVERDRIVE types: NATURAL OD, WARM OD, BLUES OD (BD-2), OD-1, SD-1, CRUNCH, T-SCREAM (TS-808), TURBO OD (OD-2), CENTA OD (Klon Centaur). Knobs: DRIVE 0–120, TONE, LEVEL, BOTTOM (low end), DIRECT MIX, SOLO SW. There are also DISTORTION, METAL DISTORTION, FUZZ and the MDP versions X OVERDRIVE and X DISTORTION.

BOOSTER has MID BOOST, CLEAN BOOST and TREBLE BOOST. BOSS says MID BOOST before the AIRD PREAMP is suitable for solos.

  1. Switch on a lightly crunchy amp (for example DELUXE COMBO). Put an OVERDRIVE before it, type T-SCREAM, with DRIVE low and LEVEL high.

    You hear: the amp distorts more. Switch the overdrive on and off to compare.

  2. Turn BOTTOM to the left and to the right.

    You hear: less or more low end in the distortion.

Sources: PG · OVERDRIVE, PG · BOOSTER.

Modulation

CHORUS, PRIME CHORUS, FLANGER, PRIME FLANGER, PHASER, SCRIPT PHASER, PRIME PHASER, CLASSIC-VIBE, ROTARY, VIBRATO, PRIME VIBRATO, TREMOLO, PAN, RING MODULATOR, SLICER and HUMANIZER. On most you turn RATE (speed), DEPTH (depth) and EFFECT LEVEL.

  1. Put a CHORUS after the amp. Start with RATE low and DEPTH halfway.

    You hear: a floating sound. Higher RATE = faster floating.

  2. Replace the chorus with a TREMOLO and turn RATE.

    You hear: the volume pulses, faster or slower.

Sources: PG · EFFECTS, RM · TARGET list.

Delay with tap tempo

DELAY: TIME 1 to 2000 ms, or a note value that follows the tempo (BPM). FEEDBACK 0–100 (number of repeats), EFFECT LEVEL 0–120, HIGH CUT, CARRYOVER. Other delays: DELAY PLUS (MONO, DIR/EFX, STEREO, PAN, REVERSE, DUAL), ANALOG DELAY, SPACE ECHO, SHIMMER DELAY, TERA ECHO.

Tap tempo works through the tempo of the memory (MASTER BPM, 40 to 250). You tap it in with a footswitch that is set to BPM TAP.

  1. Put a DELAY after the amp. Set TIME to a note value instead of milliseconds.

    You see: a note symbol instead of ms.

    Where the note values sit in the TIME range (before or after the ms): not verified. Turn through the whole list.

  2. Press CTL/EXP, tap CONTROL FUNCTION. With SELECT choose the CTL 1 line (C1) and set the function with 1 to 4 to BPM TAP.

    You see: BPM TAP at CTL 1.

  3. Tap C1 a few times in tempo.

    You hear: the repeats fall in your tempo.

  4. If you want the tempo to stay put when you change memory, set TEMPO HOLD in the MASTER block to ON.

    You hear: the same tempo after a memory change.

If MIDI clock comes in from outside, MASTER BPM follows that clock and you cannot set it. Then set SYNC CLOCK to INTERNAL (MENU → MIDI).

Sources: PG · DELAY, PG · DELAY PLUS, PG · CONTROL FUNCTION, PG · MASTER, PG · MIDI SETTING.

Reverb

REVERB types: HALL S, HALL M, PLATE, ROOM, STUDIO. TIME 0.1 to 10 s, PRE-DELAY 0 to 200 ms, DENSITY, LOW CUT, HIGH CUT, CARRYOVER. Also REVERB PLUS and SHIMMER REVERB.

  1. Put a REVERB as the last effect before MASTER, type ROOM, then HALL M.

    You hear: a small room against a hall.

  2. Set PRE-DELAY to 40 to 60 ms.

    You hear: the reverb starts just a little later than your note.

  3. Set CARRYOVER to ON and switch the reverb off while it is still sounding.

    You hear: the reverb tail rings out instead of stopping abruptly.

Sources: PG · REVERB, RM · Carryover.

Check off

Chapter 07

Serial, parallel, two amps

Serial means: everything one after the other, as in chapter 3. Parallel means: the signal splits into channel A and B and then comes back together. The split point is called DIVIDER, the merge point MIXER. When you drag the icon from the palette, they arrive in the chain together. You have one per memory.

INPUT NS DIVIDERsplits AIRD PREAMP 1JC-120 (clean) AIRD PREAMP 2BRIT STACK (crunch) MIXERmerges DLY REV MASTER AB SINGLE: A or BDUAL: A and B together STEREO or PAN L/RA/B BALANCE, SPREAD OUT
Two amps in parallel. The divider decides whether A, B or both sound; the mixer decides the balance and the stereo image.
ParameterValuesWhat it does
DIVIDER MODESINGLE, DUALSINGLE: one channel at a time. DUAL: both.
CH SELECTA, BWith SINGLE: which channel sounds.
MIX MODESWITCH, MIXSWITCH: switches at the mixer, noise from the old channel drops away. MIX: switches at the divider, tails of delay and reverb ring out.
A/B: DYNAMICOFF, POLARITY+, POLARITY-With DUAL: hard or, the other way round, soft picking goes to that channel.
A/B: FILTEROFF, LPF, HPF + CUTOFFWith DUAL: lows to one channel, highs to the other (100 Hz to 4 kHz).
MIXER MODESTEREO, PAN L/RSTEREO: mixed. PAN L/R: A left, B right.
A/B BALANCE · SPREAD100:0–0:100 · 0–100With DUAL: the ratio, and delaying B slightly for space.

Sources: PG · DIVIDER/MIXER, RM · Switching tones, PG · AIRD PREAMP.

Steps: two amps at once

  1. Press EFFECTS, tap EFFECTS PALETTE and drag DIVIDER/MIXER after the NS.

    You see: the chain splits into an upper (A) and a lower (B) branch.

  2. Put your existing amp in branch A (drag it). Drag a second AIRD PREAMP to branch B. Choose JC-120 in A and BRIT STACK in B.

    You see: two amp blocks one below the other.

  3. Tap the divider and set MODE to DUAL. Tap the mixer and set MODE to PAN L/R.

    You hear: in your headphones, clean on the left and crunch on the right.

  4. Put the mixer back to STEREO and turn A/B BALANCE.

    You hear: a mix that slides from clean to crunch.

Steps: switching with a footswitch

  1. Set the divider to SINGLE and MIX MODE to MIX.

    You hear: only channel A.

  2. CTL/EXP → CONTROL FUNCTION, line CTL 1: function DIV CH.SEL.

    You see: DIV CH.SEL at CTL 1. Factory presets such as P01-3 STUDIO BLUES use this too.

  3. Play with the delay on and press C1.

    You hear: you jump from A to B without a gap, and the delay tail keeps ringing.

Sources: PG · CONTROL FUNCTION, PG · Sound list.

Check off

Chapter 08

Saving

What is not saved is gone: when you change memory, when you switch off and with AUTO OFF. You can only save to a user slot, U01-1 to U50-4. Factory presets are read-only, but you can write them to a user slot.

Steps: saving with a name

  1. Press WRITE and tap WRITE (or press knob 1).

    You see: the WRITE screen with the target slot and the name.

  2. Choose the target slot with 1. Hold 1 down and turn to jump by bank.

    You see: the number and the name you are about to overwrite.

  3. Name: PAGE ◀ ▶ moves the cursor, SELECT chooses the letter. Turn 2 for the kind of characters, turn 3 for capital or small letters. Press 3 = delete letter, press 4 = insert space. DELETE ALL clears everything.

    You see: for example "GUITAR CLN".

  4. Tap EXEC: [WRITE] or press WRITE again.

    You see: your memory with the new name on the play screen. Switch away and back: your settings are still there.

Other WRITE functions

FunctionKnobWhat it does
WRITE1Save the current memory to a user slot. This is also how you copy: choose a memory and write it to another slot.
EXCHANGE2Swap two user memories.
INITIALIZE3Return a user memory to the default, to start from zero. The old content is gone.
INSERT4Insert; everything after it moves up one slot. Note: U50-4 falls off.

Copying, moving and saving whole sets is easier in BOSS Tone Studio (chapter 11). Make a backup there first before you use INITIALIZE or INSERT.

Sources: RM · Saving a memory, PG · WRITE, PG · EXCHANGE, PG · INITIALIZE, PG · INSERT, RM · Memory.

Check off

Chapter 09

Footswitches and expression pedal

There are two ways to play. In Memory mode you choose a memory with 1 to 4. In Manual mode the same switches turn individual functions on and off, like a pedalboard. Factory setting: a long press on C2/TUNER switches between the two. You can also choose it via MENU → CONTROL MODE.

WhereWhat you set
CTL/EXP → CONTROL FUNCTIONFixed functions per switch and pedal: BANK, MEMORY ±1, BPM TAP, TUNER, MEMORY/MAN, AMP CTL, WAH, DIV CH.SEL, SEND/RETURN, LOOP CTL, LOOPER STOP, LOOPER CLEAR, MIDI START. With MODE TOGGLE or MOMENT. With PREF per memory or for the whole system.
CTL/EXP → ASSIGN SETTINGSTwenty free assignments (ASSIGN 1 to 20): a source (switch, pedal, MIDI CC) controls a parameter between MIN and MAX. Here you also set the Manual switches MAN 1 to MAN 4.
Long press on 1…4 in an effectQuick assign: jumps to ASSIGN SETTINGS with that parameter already filled in.

Steps: delay on and off with C1

  1. Press CTL/EXP and tap ASSIGN SETTINGS. With SELECT choose a number that is still off.

    You see: the line of that ASSIGN number.

  2. With 1 to 4 and PAGE ◀ ▶ set: TARGET = DELAY, ON/OFF. MIN = OFF, MAX = ON. SOURCE = CTL 1. MODE = TOGGLE.

    You see: all the boxes filled in.

  3. Press SELECT to switch this ASSIGN on.

    You see: the NUM box turns green.

  4. Press C1.

    You hear: the delay goes on and off. Save with WRITE.

If C1 already has a function in this memory under CONTROL FUNCTION, set that to OFF. Whether both would otherwise work at the same time: not verified.

The pedal: wah and volume

For EXP1 PEDAL you choose under CONTROL FUNCTION: FOOT VOL, WAH, FV/WAH, FV+TUNER or FV+TUNER/WAH. The wah and volume functions only appear if there is a WAH and/or FOOT VOLUME block in the chain. If there are several, the pedal controls the first block in the chain.

The toe switch is called EXP1 SW: press the front of the pedal down firmly. Almost all factory presets use EXP1 SW = WAH and EXP1 = FV/WAH.

  1. Choose P01-1 GX DUAL DRIVE. Move the pedal.

    You hear: the volume goes up and down.

  2. Press the toe down firmly.

    You see: the PEDAL FX light comes on. You hear: the pedal now controls the wah.

    That FV/WAH controls the volume with wah off and the wah with wah on is not literally in the manual: not verified. It follows from the function names and the presets.

  3. Tap the WAH block and try WAH TYPE: CRY WAH, VO WAH, FAT WAH, LIGHT WAH, 7STRING WAH, RESO WAH. With PEDAL MIN and PEDAL MAX you set the range.

    You hear: a different wah character and range.

  4. With FOOT VOLUME you set VOLUME MIN, VOLUME MAX and VOLUME CURVE (SLOW1, SLOW2, NORMAL, FAST).

    You hear: how fast the volume swells changes.

  5. If the volume does not close completely, or the toe does not switch: MENU → HARDWARE SETTINGS → PEDAL CALIBRATION. Heel down, WRITE. Toe down, WRITE. Toe firm, see whether PEDAL FX lights up (sensitivity with 4), WRITE.

    You see: "COMPLETED!".

Extra pedals can go in CTL 3, 4/EXP 2: expression pedals EV-30, FV-500L, FV-500H or Roland EV-5, and footswitches FS-5U, FS-6 or FS-7. BOSS advises against other expression pedals.

Sources: RM · Control mode, PG · CONTROL FUNCTION, RM · ASSIGN SETTING, RM · Quick assign, RM · Assigning a function, PG · WAH, PG · FOOT VOLUME, PG · Sound list, RM · Pedal calibration, RM · External pedals.

Check off

Chapter 10

Looper

The looper records 38 seconds in mono or 19 seconds in stereo. It is a block in the chain, so you have to place it first. Then you give it a footswitch. You do not need extra switches: C1 can do everything.

  1. Press EFFECTS → EFFECTS PALETTE and drag the looper (LOOP) into the chain.

    You see: the LOOP icon in the chain.

    Where you put it decides which effects are in your recording and which still work on the playback afterwards: not verified, follows logically from the chain. Start at the end, just before MASTER.

  2. CTL/EXP → CONTROL FUNCTION, line CTL 1: function LOOP CTL.

    You see: C1 lights up blue: the looper is ready, still empty.

  3. Press C1 and play a few bars. Press C1 again on the one.

    You see: red while recording, then green. You hear: your loop plays around.

    This applies if LOOP REC ACTION is set to record → play → overdub (see the tip below). Which order is on by default: not verified.

  4. Press C1 to play along (overdub), and again to go back to playing.

    You see: orange during overdub. You hear: your second layer on top.

  5. Stopping: press C1 twice quickly. Clearing: hold C1 down for a long press.

    You see: green blinking = stopped with a recording in it; blue = empty.

  6. Is your playing buried under the loop? Tap the LOOP icon and with 1 set PLAY LEVEL below 100.

    You hear: the loop softer than what you play live.

Under MENU → PLAY OPTION: LOOP MODE (MONO 38 s or STEREO 19 s) and LOOP REC ACTION (record → play → overdub, or record → overdub → play). With COLOR MODE TYPE 2 the colors are different: overdub yellow, play blue.

Sources: RM · Looper, PG · PHRASE LOOP, PG · PLAY OPTION.

Check off

Chapter 11

BOSS Tone Studio on the Mac

Would you rather see all the knobs of an effect at once? That is what GX Board is for. GX Board and BOSS Tone Studio cannot be open at the same time.

BOSS Tone Studio (BTS) for GX-100 works over the USB cable. You need two downloads from the BOSS support page: first the GX-100 Driver, then BTS. For the IR LOADER you need BTS 2.0.0 or newer.

Installing and starting

  1. Download the GX-100 Driver at boss.info, Updates & Drivers. Double-click and follow the steps.

    You see: "Installation has been completed."

  2. Download BTS, unzip the ZIP and install.

    You see: "The installation was successful."

  3. On the GX-100 set MENU → USB → USB DRIVER to VENDOR. That is the setting for macOS.

    You see: VENDOR selected.

  4. Connect the USB cable, switch on the GX-100. In the Finder open Applications › BOSS › GX-100 › BOSS TONE STUDIO for GX-100. The first time: read the terms of use and click ACCEPT. Choose "GX-100" and OK.

    You see: after loading, the Editor with your memories.

Editing in the Editor

Click EDITOR at the top and then "USER" and a memory. In the middle you see the chain, at the top the palette. Click a block and the parameters are at the bottom. Drag a knob up or down, use the scroll wheel, or double-click and type a value. With the DELETE, INSERT and OVERWRITE buttons you place blocks. At the top there are also CTL/EXP, IN/OUT SETTINGS and WRITE, just like on the unit.

  1. Click the amp block and choose another type in the [TYPE] box.

    You hear: the GX-100 changes amp straight away.

  2. At the top right click WRITE, choose a user slot, type a name and click WRITE.

    You see: the new name on the GX-100 screen too.

Liveset in the Librarian

A liveset is a collection of memories in BTS. You can make 30 of them, with a maximum of 300 memories per set.

  1. Backup. Click LIBRARIAN → Import → GX-100. Give the set a name ("Backup 12-11").

    You see: "Completed!!" and a liveset with all your user memories.

  2. Saving as a file. Export → choose the set → FILE.

    You see: a .tsl file on your Mac.

  3. Restoring one memory. Drag a memory from a liveset onto a user slot of the GX-100. That slot is overwritten.

    You see: the memory in that slot, on the unit too.

  4. Copying and moving. Dragging copies. If it lands on a red area, it overwrites; on a red line it is inserted. To move: hold the Alt key while dragging. To choose several: Shift (a range) or Command (separate ones).

    You see: the memories in their new place.

    The manual says "Alt". On a Mac keyboard that key is called Option (⌥): not verified in the BTS manual.

  5. Whole set back to the GX-100. Export → choose the set → GX-100. More than 200 memories are not restored.

    You see: "Completed!!".

Under MENU in BTS there is also ALL DATA BACKUP: all memories plus system settings in one go to the Mac, and back.

Tone Exchange

  1. In BTS click the Tone Exchange button and at the top "Sign in". Log in with your Roland account. Your Mac must be online.

    You see: the Tone Exchange list.

  2. Search by keyword or genre and click Download. You always get a whole liveset, not a single memory.

    You see: the set in the Librarian. Drag a memory from it to the GX-100 and play.

  3. To share your own: LIBRARIAN → upload icon → choose a set → fill in the info → Upload.

    You see: the upload starts.

Loading your own IR

  1. At the top click IR LOADER → LOAD and choose a WAV (44.1, 48 or 96 kHz, 16 or 24 bit).

    You see: BTS converts the file. That takes a moment.

  2. Choose a slot USER-1 to USER-16 and click OK.

    You see: you are back on the IR Loader screen.

  3. On the GX-100: amp block, page 4, knob 3 (SP TYPE), all the way at the end.

    You hear: your IR as the speaker cabinet.

Sources: BTS · Driver, BTS · Install, BTS · Start, PG · USB, BTS · Editor, BTS · WRITE, BTS · Librarian, BTS · Import, BTS · Export, BTS · File, BTS · Liveset, BTS · Copy, BTS · Move, BTS · Backup, BTS · Tone Exchange, BTS · IR LOADER, SUP 4, Video BTS.

Check off

Chapter 12

Recording in Logic

The GX-100 is also an audio interface. Over one USB cable it sends four channels to Logic: 1/2 MAIN is your sound with effects, 3/4 DRY is the dry guitar. It works at 48 kHz. The other way round, Logic can send sound back: to 1/2 for playback, or to 3/4 to go through the effects again (reamping).

GX-100 INPUTguitar effect chainamp, delay, ... output stagemix with computer PHONES 1/2 MAIN · processed 3/4 DRY · dry DIRECT MONITOR ON = you hear this Mac · Logic track "wet" (stereo)input 1-2 track "dry" (mono)input 3 master / playbackoutput 1-2 play reamp trackoutput 3-4 1/2: without effects 3/4: through the effects MIX LEVEL DRY TO EFX EFX OUT LEVEL DRY OUT
What travels over the USB cable. The gray names on the right are the level controls under MENU → USB (0 to 200%). Dashed: only for reamping.

Sources: SUP 1, SUP 2, SUP 3, PG · USB, RM · Computer, RM · Specs.

One-time setup

  1. GX-100 Driver installed and USB DRIVER = VENDOR (chapter 11). USB cable into the Mac.

    You see: the GX-100 as an audio device on the Mac.

  2. In Logic: Logic Pro › Settings › Audio › Devices. Choose the GX-100 as both output and input device. Apple advises against using different devices for in and out. So let your MiniFuse 1 rest during guitar recordings.

    You see: below the I/O buffer size, the delay in ms.

  3. New project: File › Project Settings › Audio and set the sample rate to 48 kHz. Do this before you record.

    You see: 48 kHz in the menu. Apple warns: do not change this after recording, or files may play at the wrong pitch and speed.

  4. In Logic: Settings › Audio › General, switch Software Monitoring off. On the GX-100 DIRECT MONITOR (MENU → USB) is set to ON; it is that way every time you switch on.

    You hear: your guitar without delay in the headphones on the GX-100.

The menu names in Logic are given here in English, as Apple names them: "Logic Pro > Settings > Audio > Devices", "File > Project Settings > Audio" and "Software monitoring". The exact names in the language of your Logic version: not verified.

Recording: wet and dry at once

  1. Make a stereo audio track with input 1-2 ("wet") and a mono audio track with input 3 ("dry").

    You see: both tracks move on their meter when you play.

    Whether channels 3 and 4 both carry the same dry guitar: not verified. See which meter moves.

  2. Too soft or too loud in Logic? On the GX-100 adjust MENU → USB: EFX OUT LEVEL for 1/2, DRY OUT for 3/4.

    You see: the meters in Logic rise or fall, without red.

  3. Arm both tracks for recording and record.

    You hear: on playback your effect sound. The dry track sounds bare; that is fine.

Reamping later

  1. Set the output of the dry track to 3-4 (GX-100 DRY).

    You see: output 3-4 on the channel of that track.

  2. Make a new stereo track with input 1-2. Play the dry track.

    You hear: your old take through the current GX-100 sound. Turn the amp and effects until it is right.

  3. Is the signal going into the effects too soft? Adjust DRY TO EFX (MENU → USB).

    You hear: the amp reacts as with live playing.

  4. Arm the new track for recording and play back.

    You see: a new wet take, perfectly in time with the dry one.

No GX-100 effects on playback

If you hear your Logic mix with reverb or distortion over it, the output is set to 3-4 (DRY). Set the master output to 1-2 (MAIN). You control its volume with MIX LEVEL. Leave LOOPBACK on OFF: with ON the mix of computer and GX-100 goes back to the Mac, and then DIRECT MONITOR does not work.

Sources: SUP 1, SUP 2, SUP 3, PG · USB, Apple · Devices, Apple · Audio devices, Apple · Sample rate, Apple · General Audio, Apple · Input monitoring, Apple · Latency.

Check off

Chapter 13

MIDI to a synthesizer

With MIDI you let the GX-100 control your synthesizer. It can send two things: a program change when you choose a memory, and CC messages from C1, C2, the pedal and external pedals. What it does not do: turn your guitar notes into MIDI notes. The manual only mentions program changes, CCs, clock and data; notes are not mentioned anywhere.

GX-100 memory · C1 · C2 · EXP MIDI OUT synthesizer scene 1 to 256 MIDI IN 5-pin MIDI cable choose memory → Bank MSB 85 · LSB 0 · PC = scene on the Ctrl Ch of your synthesizer C1 / C2 / EXP / CTL 3-4 → CC# 1–31 or 64–95, on TX CHANNEL guitar notes → MIDI notes:not possible
The MIDI connection. The Reference Manual shows such a MIDI OUT-to-IN cable as an example.

Changing scene when you change memory

  1. Connect MIDI OUT of the GX-100 to MIDI IN of your synthesizer.

    You see: nothing yet; the settings follow.

  2. On your synthesizer: [MENU] → SYSTEM (with [ENTER]) → Ctrl Ch. Choose a channel, for example 16. Save with [SHIFT] + [MENU] and [ENTER].

    You see: Ctrl Ch = 16.

  3. On the GX-100: choose the memory that goes with a scene. CTL/EXP → MEMORY MIDI. At MEMORY MIDI 1: CH = 16, BANK MSB = 85, BANK LSB = 0, PC# = the scene number (1 to 128). For scene 129 to 256: LSB = 1 and PC# = scene minus 128.

    You see: the values in MEMORY MIDI 1.

  4. Save the memory with WRITE. Choose another memory and then this one again.

    You see: your synthesizer jumps to the chosen scene.

Two things to watch. 1. For BANK MSB/LSB the Parameter Guide gives the range "OFF, 1–128" (your synthesizer expects 85 and 0). If your screen shows 1 to 128, you may have to choose 86 and 1: not verified. Test it: if your synthesizer lands on the wrong scene, shift it up by one. 2. For MEMORY MIDI the Parameter Guide writes that the message goes "via USB". The Reference Manual shows a MIDI cable. Whether MEMORY MIDI also comes out of MIDI OUT: not verified. If it does not work over the cable, use ASSIGN to set a MIDI PC target on C1 (TARGET MIDI PC# with MSB and LSB 0–127) or send from Logic.

CCs from the switches and pedals

  1. MENU → MIDI → MIDI SETTINGS. Set TX CHANNEL to the channel of the part of your synthesizer that you want to control.

    You see: the channel at TX CHANNEL.

  2. In the same list set CTL1 CC#, CTL2 CC#, EXP1 CC# or EXP2 CC# to a number. Possible: CC#1 to 31 and CC#64 to 95.

    You see: the CC number at that switch.

  3. Press C1 or move the pedal.

    You hear: your synthesizer reacts, if that CC controls something there.

    Which CC your synthesizer links to which function is not in the BOSS documentation and was not looked up in the manual of your synthesizer: not verified. Try CC#64 (in the MIDI standard the sustain pedal) and CC#11 (expression) as a starting point.

More: CLOCK OUT = ON sends the tempo clock of the GX-100 along, and the switch function MIDI START starts and stops external devices. What your synthesizer does with that: not verified.

Sources: RM · MIDI, PG · MEMORY MIDI, PG · MIDI SETTING, RM · ASSIGN SETTING, PG · CONTROL FUNCTION, Roland · choosing scenes via MIDI.

Check off

Chapter 14

Troubleshooting

Noise and hum

  1. Put a NOISE SUPPRESSOR early in the chain and raise THRESHOLD (chapter 6).

    You hear: silence between your notes.

  2. Turn the amp GAIN back a little or set GAIN SW one setting lower.

    You hear: less hiss, usually with enough distortion left.

  3. Is INPUT SENS too high? Set it again as in chapter 1.

    You see: the yellow peak only on your hardest strike.

  4. The GND LIFT switch on the back is for hum when an amp is connected to SEND/RETURN. Normally: OFF.

    You hear: in your setup without an amp it probably changes nothing.

Too soft or too loud

WhereWhat
OUTPUT LEVELOverall volume of the unit.
MEMORY LEVEL (MASTER block, 1–200)Volume of one memory. This is how you make your memories equally loud.
LEVEL in amp and effectsVolume per block. BOSS warns: do not set the AIRD level too high.
INPUT SENSInput. Yellow peak only when you strike hard.
EFX OUT LEVEL · DRY OUTLevel to Logic (1/2 and 3/4).
MIX LEVELVolume of Logic in your headphones.
OUTPUT SETTING (-10 / +4 dBu)Only for the OUTPUT jacks: -10 dBu to a guitar amp, +4 dBu to a mixer or recorder.

Strange sound via Logic

What you hearLikely causeWhat to do
Effects over your Logic playbackOutput is set to 3-4 (DRY)Master output to 1-2 (MAIN).
Doubled, floating or with echoYou hear the GX-100 directly and also via Logic with delaySoftware monitoring in Logic off, or the track not on input monitoring. not verified as the cause; it follows from how both monitoring routes work.
Everything sounds too high or too low, or too fastSample rate differs from the recordingSet the project to 48 kHz before you record.
You do not hear your guitarDIRECT MONITOR is off, or LOOPBACK is onMENU → USB: DIRECT MONITOR ON, LOOPBACK OFF.
Message "USB MIDI OFFLINE!"Problem with the USB cableCheck or replace the cable.
Clicks and ticksI/O buffer too small for your MacLogic › Settings › Audio › Devices: buffer one step larger.

Other

  • Quickly switch all effects off to hear your bare guitar: in the tuner set TUNER OUTPUT to BYPASS and switch the tuner on. That setting is kept.
  • Effect does not fit: see the messages in chapter 3 (CHAIN IS FULL, DSP RESOURCE IS FULL).
  • Pedal does not close completely or the toe does not respond: PEDAL CALIBRATION (chapter 9).
  • Knobs or screen do nothing: maybe LOCK is on. Hold EXIT down on the play screen.
  • Everything back to factory: first a backup in BTS. Then MENU → FACTORY RESET, choose the range with 1 and 2 (FROM/TO: SYSTEM and/or memories), EXEC: [WRITE], OK.

Sources: PG · NS, RM · Connecting, PG · MASTER, PG · AIRD, PG · USB, PG · OUTPUT SETTING, SUP 1, SUP 5, Apple · Sample rate, Apple · Latency, RM · Errors, PG · LOCK, RM · Factory reset.

Check off

Sources

Where it comes from

Checked on 12 November 2026. RM = GX-100 Reference Manual v2.00, PG = GX-100 Parameter Guide v2.00, BTS = BOSS TONE STUDIO for GX-100 (PC) v2.00, SUP = Roland support article. All links open in a new tab.

Reference Manual v2.00

  1. RM · Connecting the equipmentConnecting the equipment
  2. RM · PowerTurning the power on/off
  3. RM · Auto OffMaking the power automatically turn off after a time (AUTO OFF)
  4. RM · InputConfiguring the input to match the instrument you connect
  5. RM · Output selectSpecify the type of amplifier you have connected
  6. RM · VolumeAdjusting the volume
  7. RM · TunerUsing the tuner
  8. RM · MemorySelecting a memory
  9. RM · FootswitchesSelecting a memory using footswitches on the top panel
  10. RM · Touch panelSelecting a memory using the touch panel
  11. RM · Play screenAbout the play screen
  12. RM · KnobsAssigning favorite parameters to [1]–[4] knobs
  13. RM · Control modeSelecting the control mode
  14. RM · Effect editingBasic procedure for effect editing
  15. RM · Effect placementEffect placement
  16. RM · Switching tonesSwitching tones without interrupting the sound
  17. RM · CarryoverPreserving the tail of the effect (carryover)
  18. RM · Saving a memorySaving a memory
  19. RM · MenuBasic menu operations, display brightness, colors
  20. RM · Factory resetRestoring the factory settings
  21. RM · ComputerConnecting to a computer
  22. RM · MIDIConnecting with an external MIDI device
  23. RM · Assigning a functionAssigning a function
  24. RM · ASSIGN SETTINGASSIGN SETTING
  25. RM · Quick assignMaking assignments from the effect edit screen
  26. RM · TARGET listTARGET list
  27. RM · Pedal calibrationAdjusting the expression pedal
  28. RM · External pedalsConnecting external pedals
  29. RM · LooperLooper
  30. RM · ErrorsError message list
  31. RM · SpecificationsMain specifications

Parameter Guide v2.00

  1. PG · EFFECTSEFFECTS (overview)
  2. PG · COMPRESSORCOMPRESSOR
  3. PG · X-COMPRESSORX-COMPRESSOR
  4. PG · BOOSTERBOOSTER
  5. PG · OVERDRIVEOVERDRIVE
  6. PG · AIRD PREAMPAIRD PREAMP
  7. PG · AIRD PREAMP TYPE listAIRD PREAMP TYPE list
  8. PG · SP TYPE listSP TYPE list
  9. PG · MIC TYPE listMIC TYPE list
  10. PG · PARAMETRIC EQPARAMETRIC EQUALIZER
  11. PG · GRAPHIC EQGRAPHIC EQUALIZER
  12. PG · DELAYDELAY
  13. PG · DELAY PLUSDELAY PLUS
  14. PG · REVERBREVERB
  15. PG · WAHWAH
  16. PG · FOOT VOLUMEFOOT VOLUME
  17. PG · NOISE SUPPRESSORNOISE SUPPRESSOR
  18. PG · DIVIDER/MIXERDIVIDER/MIXER
  19. PG · PHRASE LOOPPHRASE LOOP
  20. PG · AIRD BASS PREAMPAIRD BASS PREAMP
  21. PG · MASTERMASTER
  22. PG · Max effects / DSPMaximum number of effects and functional devices
  23. PG · CONTROL FUNCTIONCONTROL FUNCTION
  24. PG · MEMORY MIDIMEMORY MIDI
  25. PG · LOCKLOCK
  26. PG · PLAY OPTIONPLAY OPTION
  27. PG · MIDI SETTINGMIDI SETTING
  28. PG · USBUSB
  29. PG · OUTPUT SELECTOUTPUT SELECT
  30. PG · GLOBAL EQGLOBAL EQ
  31. PG · OUTPUT SETTINGOUTPUT SETTING
  32. PG · WRITEWRITE (Saving to memory)
  33. PG · EXCHANGEEXCHANGE
  34. PG · INITIALIZEINITIALIZE
  35. PG · INSERTINSERT
  36. PG · Sound listSound list (presets with CTL1, EXP1 SW, EXP1)

BOSS TONE STUDIO for GX-100 (PC) v2.00

  1. BTS · DriverInstalling the USB driver
  2. BTS · InstallInstalling TONE STUDIO
  3. BTS · StartStarting TONE STUDIO
  4. BTS · EditorEditor basic screen, Editing the Effects
  5. BTS · WRITESaving an edited effect (WRITE)
  6. BTS · LibrarianLIBRARIAN basic screen
  7. BTS · ImportIMPORT FROM GX-100
  8. BTS · ExportEXPORT TO GX-100
  9. BTS · FileEXPORT TO FILE, IMPORT FROM FILE
  10. BTS · LivesetCreating an original liveset
  11. BTS · CopyCopying a memory, overwrite vs insert
  12. BTS · MoveMoving a memory
  13. BTS · IR LOADERLoading IR data into the GX-100
  14. BTS · Tone ExchangeWhat you can do with BOSS TONE EXCHANGE
  15. BTS · BackupALL DATA BACKUP

Roland support

  1. SUP 1GX-100: How to prevent effects from being applied to computer audio playback via USB
  2. SUP 2GX-100: Applying GX-100 effects to DAW playback audio and recording as a new track
  3. SUP 3GX-100: Using DAW software to record the guitar sound with effects
  4. SUP 4GX-100: How do I load IR (Impulse Response) data?
  5. SUP 5GX-100: How to bypass all Effects and Amp Modeling at once

BOSS and Roland, other

  1. ProductBOSS GX-100 product page (NL)
  2. VideosQuick Start: Overview, Control Settings, Four Cable Method, BOSS Tone Studio. Titles checked; the content of the videos was not read word for word.
  3. DownloadsGX-100 Updates & Drivers and Owner's Manuals. The MIDI Implementation PDF asks you to agree to a license and was not opened.
  4. Roland · choosing scenes via MIDISelecting Scenes via MIDI (Roland Support)

Apple, Logic Pro

  1. Apple · DevicesAudio Devices settings in Logic Pro for Mac
  2. Apple · Audio devicesUsing audio devices with Logic Pro for Mac overview
  3. Apple · Sample rateSet the sample rate of a project in Logic Pro for Mac
  4. Apple · General AudioGeneral Audio settings in Logic Pro for Mac
  5. Apple · Input monitoringUse input monitoring with tracks in Logic Pro for Mac
  6. Apple · LatencyManage input monitoring latency in Logic Pro for Mac
This workbook was written by the makers of GX Board. All product names belong to their owners. The workbook changes nothing on your devices.