SPACE ECHO
A tape echo with three heads, a wavering tone and ducking.
What it does
SPACE ECHO imitates a three-head tape echo. You choose which heads play, and that sets the rhythm of the repeats.
The echoes sound soft and a little uneven. WOW&FLUTTER makes the pitch of the repeats waver slightly, like an old tape.
How to use it
- Choose HEAD 1+2+3 for a busy echo pattern that follows your playing.
- Raise WOW&FLUTTER for an echo that sounds a bit out of tune and alive.
- Let the FEEDBACK build up for floating, wavering repeats under long chords.
- Use the ducking to let the echo step back while you play.
Where it goes in the chain
After the amp or at the end of the chain, before the reverb. The echoes stay soft and the reverb sits around them.
Starting points
Classic tape
TIME 350ms · FEEDBACK 35 · EFFECT LEVEL 50 · HEAD 1+2 · WOW&FLUTTER 40
A soft tape echo with two repeats and a light unevenness.
Busy pattern
TIME 300ms · FEEDBACK 40 · EFFECT LEVEL 45 · HEAD 1+2+3 · HIGH CUT 5.00kHz
Many repeats at different distances, lovely under long notes.
Floating
TIME 500ms · FEEDBACK 60 · EFFECT LEVEL 40 · HEAD 2+3 · WOW&FLUTTER 65
Slow, uneven repeats that drift away.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TIME | 1ms / 2ms / 3ms / 4ms … 1/1D / 2/1 (2018 steps) | The time between repeats, in milliseconds or as a note value such as 1/4 or 1/8D. A note value follows the tempo (BPM) of the memory. |
| FEEDBACK | 0 to 100 | How much of the echo comes back. Low gives a few repeats, high a long, floating tail. |
| EFFECT LEVEL | 0 to 120 | The volume of the echoes. Start around 40 to 50 and raise it until you just hear them in the mix. |
| DIRECT LEVEL | 0 to 100 | The volume of your dry signal. At 100 your guitar stays as it was. |
| HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cuts the high end of the echoes. FLAT lets everything through; lower gives darker repeats. |
| MOD RATE MOD DEPTH | 0 to 100 | Adds extra waver to the echoes. RATE is the speed, DEPTH the amount. At DEPTH 0 you hear nothing. |
| DUCK SENS | 0 to 100 | How sensitive the ducking is to your playing. Higher means the echo steps back sooner. |
| DUCK PRE | 0 to 100 | Turns down the signal going into the echo while you play loudly. Closer to 100 gives a stronger reduction. |
| DUCK POST | 0 to 100 | Turns down the output of the echo while you play loudly. Closer to 100 gives a deeper reduction. |
| HEAD | 1 / 1+2 / 1+3 / 2+3 / 1+2+3 | Picks which playback heads sound. Head 2 gives twice the delay time of head 1, head 3 three times. Combined heads lay several repeats over each other. |
| WOW&FLUTTER | 0 to 100 | Makes the pitch of the echoes waver slightly, like an old tape. Low is steady, high sounds out of tune and alive. |
| CARRYOVER | OFF / ON | ON lets the echoes ring out after you switch the effect off. OFF cuts them off at once. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. SPACE ECHO in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Echo
Turn it yourself?
In GX Board, SPACE ECHO is a device in your rack, with all its controls on the front.