SHIMMER REVERB
A reverb with a sparkling high end, from one or two pitch-shifted voices.
What it does
SHIMMER REVERB is a reverb with one or two shifted voices ringing along. By default they sound one and two octaves above what you play.
That gives a glittering, floating layer that hangs around your chords. PITCH and LEVEL set each voice separately.
How to use it
- Set a long TIME and play slow chords for a glittering cloud behind your playing.
- Set LEVEL 2 to 0 for a simpler reverb with only an octave above.
- Set PITCH 1 to -12 for a dark, deep layer under the reverb.
- Keep EFFECT LEVEL low in a band, so the shimmer does not fill the mix.
Where it goes in the chain
As the last effect in the chain, after the echoes. The shifted voices then ring around everything you play.
Starting points
Glitter cloud
TIME 5.0s · EFFECT LEVEL 30 · PITCH 1 12 · PITCH 2 24 · LEVEL 1 100 · LEVEL 2 60
A long cloud with voices one and two octaves higher.
Single octave
TIME 3.0s · EFFECT LEVEL 25 · PITCH 1 12 · LEVEL 1 80 · LEVEL 2 0
A soft reverb with only an octave above.
Deep layer
TIME 4.0s · EFFECT LEVEL 30 · PITCH 1 -12 · LEVEL 1 70 · PITCH 2 12 · LEVEL 2 40 · TONE -10
A dark layer below and a light one above, for a big space.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TIME | 0.1s / 0.2s / 0.3s / 0.4s … 9.9s / 10.0s (100 steps) | How long the reverb lasts. Higher gives a longer floating layer. For glittering chords, 3 to 6 seconds is common. |
| TONE | -50 to 50 | Shapes the overall tone of the reverb. Move it to either side of 0 and listen. |
| EFFECT LEVEL | 0 to 100 | The volume of the reverb. Start around 20 to 30, because the shifted tones stand out quickly. |
| DENSITY | 1 to 10 | How dense the reverb is. High values sound smooth, low values let single echoes show. Choose by taste. |
| PRE-DELAY | 0 to 200 | The time between your note and the start of the reverb. Higher keeps your playing clearer and makes the space a bit bigger. |
| LOW CUT HIGH CUT | LOW CUT: FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) HIGH CUT: 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cut the low and high end of the reverb. A higher LOW CUT and lower HIGH CUT keep the shimmer slim and soft. |
| LOW DAMP HIGH DAMP | -50 to 50 | LOW DAMP turns down the low end of the reverb, HIGH DAMP the high end. Use them to keep the reverb from clouding the mix; listen and adjust. |
| MOD RATE MOD DEPTH | 0 to 100 | Makes the reverb waver lightly. RATE is the speed, DEPTH the amount. At DEPTH 0 you hear nothing. |
| DUCK SENS | 0 to 100 | How sensitive the ducking is to your playing. Higher means the reverb steps back sooner. |
| DUCK PRE | 0 to 100 | Turns down the signal going into the reverb while you play loudly. Closer to 100 gives a stronger reduction. |
| DUCK POST | 0 to 100 | Turns down the output of the reverb while you play loudly. Closer to 100 gives a deeper reduction. |
| DIRECT LEVEL | 0 to 100 | The volume of your dry signal. At 100 your guitar stays as it was. |
| PITCH 1 PITCH 2 | -24 to 24 | The pitch of the two extra voices in semitones. 12 is an octave up, 24 two octaves, -12 an octave down, 0 no shift. |
| LEVEL 1 LEVEL 2 | 0 to 100 | The volume of the first and second shifted voice. Set one to 0 to hear only the other. |
| CARRYOVER | OFF / ON | ON lets the reverb ring out after you switch the effect off. OFF cuts it off at once. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. SHIMMER REVERB in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Reverb
Turn it yourself?
In GX Board, SHIMMER REVERB is a device in your rack, with all its controls on the front.