AIRD PREAMP
A full amp with speaker cabinet and microphone, from clean to heavy.
There is a version for bass too: AIRD BASS PREAMP
What it does
AIRD PREAMP gives you the sound of a guitar amp: preamp, tone controls and a speaker cabinet that is picked up by a microphone.
You choose an amp type, set gain and tone, then decide how the cabinet and the microphone sound. You get a complete guitar tone without a real amp.
How to use it
- Use it as the core of your preset: pick a TYPE, set GAIN and you have an amp in the chain.
- Play through headphones or a PA with SP TYPE on, so you hear a cabinet sound instead of a bare preamp.
- Set GAIN SW to LOW for an open, dynamic tone and to HIGH for more distortion and sustain.
- Use SOLO SW and SOLO LEVEL for a solo tone with its own volume, without needing another effect.
Where it goes in the chain
Put it in the middle of the chain: pedals like compressor and overdrive before it, modulation, delay and reverb after it.
Starting points
Open clean
TYPE NATURAL · GAIN 25 · LEVEL 55 · GAIN SW LOW · SP TYPE ORIGINAL
A bright, dynamic tone that stays clean when you play softly.
Warm crunch
TYPE BOUTIQUE · GAIN 60 · MIDDLE 60 · PRESENCE 30 · GAIN SW MIDDLE
Light distortion with plenty of mids, for rhythm and bluesy playing.
Tight high gain
TYPE ORNG STACK · GAIN 90 · BASS 45 · MIDDLE 55 · GAIN SW HIGH · MIC TYPE DYN421
A heavy, tight tone for riffs and solos.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TYPE | TRANSPARENT / NATURAL / BOUTIQUE / SUPREME … ORNG STACK / BGNR UB METAL (23 steps) | Picks the amp model. TRANSPARENT and NATURAL are clean, BOUTIQUE, SUPREME and X-CRUNCH are crunch, JUGGERNAUT, ORNG STACK and BGNR UB METAL are high gain. The rest sit in between. |
| GAIN | 0 to 120 | Sets how much the preamp distorts. Low stays clear and dynamic, high gets thick and long. Fine-tune it with your guitar's volume knob. |
| LEVEL | 0 to 100 | The output volume of the amp. Use it to match the volume of your other presets, not to shape the tone. |
| BASS MIDDLE TREBLE | 0 to 100 | The tone controls: low, middle and high. More MIDDLE pushes your tone forward, less gives a hollow sound. Start at 50 and move in small steps. |
| PRESENCE | 0 to 100 | Adds sharp high end at the end of the amp. More gives air and bite, less makes the tone darker and softer. |
| GAIN SW | LOW / MIDDLE / HIGH | Three gain ranges: LOW for clean to light, MIDDLE as the default, HIGH for heavy distortion. It changes how GAIN responds. |
| SOLO SW | OFF / ON | Switches to a tone made for solos. SOLO LEVEL sets the volume while it is on. |
| SOLO LEVEL | 0 to 100 | The volume while SOLO SW is on. Set it a little above your normal level to make a solo stand out. |
| BRIGHT SW | OFF / ON | Turns the bright setting on or off. It only works with certain amp types, so on others you may hear no change. |
| SAG | -10 to 10 | Sets how much the compression changes in response to the power amp. At 0 it is neutral. Move it in small steps and listen to how the playing feels. |
| RESONANCE | -10 to 10 | Sets how much the power amp and the speaker transformer affect each other, which changes how the dynamics respond. At 0 it is neutral. Try small steps both ways. |
| DIRECT MIX | 0 to 100 | Sets the volume of the direct sound, without cabinet and microphone. At 0 you only hear the cabinet sound. |
| SP TYPE | OFF / ORIGINAL / 1x8" / 1x10" … USER 15 / USER 16 (30 steps) | The speaker cabinet, named by number and size of speakers, such as 1x12 or 4x12. ORIGINAL uses the amp's own speaker, OFF turns it off, USER slots hold loaded speaker responses. |
| MIC TYPE | DYN57 / DYN421 / CND451 / CND87 / RBN121 / BLEND A / BLEND B / BLEND C / FLAT | The microphone. DYN57 and DYN421 are dynamic (DYN421 has more low end), CND451 and CND87 are condenser, RBN121 is a warm ribbon. BLEND A to C mix two mics, FLAT is neutral. |
| MIC DISTANCE | SHORT / MEDIUM / LONG | How far the microphone is from the speaker. The distance grows in the order SHORT, MEDIUM, LONG. Try them and listen to the tone. |
| MIC POSITION | CENTER / 1cm / 2cm / 3cm / 4cm / 5cm / 6cm / 7cm / 8cm / 9cm / 10cm | Where the microphone sits in front of the speaker. CENTER is the middle of the speaker cone, 1cm to 10cm moves it further from the middle. Try a few positions. |
| MIC LEVEL | 0 to 100 | The volume of the microphone sound. At 100 it is full, lower brings it down. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. AIRD PREAMP in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Amp
Turn it yourself?
In GX Board, AIRD PREAMP is a device in your rack, with all its controls on the front.